The research of river basin ecological compensation based on water emissions trading mechanism.

By integrating the successful case of the European Union emissions trading system, this study proposes a water emissions trading system, a novel method of reducing water pollution. Assuming that upstream governments allocate initial quotas to upstream businesses as the compensation standard, this approach defines the foundational principles of market trading mechanisms and establishes a robust watershed ecological compensation model to address challenges in water pollution prevention. To be specific, the government establishes a reasonable initial quota for upstream enterprises, which can be used to limit the emissions of upstream pollution. When enterprises exceed their allocated emissions quota, they face financial penalties. Conversely, these emissions rights can be transformed into profitable assets by participating in the trading market as a form of ecological compensation. Numerical simulations demonstrate that various pollutant emissions from upstream businesses will have various effects on the profits of other businesses. Businesses in the upstream region received reimbursement from the assigned emission rights through the market mechanism, demonstrating that ecological compensation for the watershed can be achieved through the market mechanism. This novel market trading system aims at controlling emissions management from the perspectives of individual enterprises and ultimately optimizing the aquatic environment.

Application of preoperative 3D printing in the internal fixation of posterior rib fractures with embracing device: a cohort study.

BACKGROUND: To explore the impact of preoperative 3D printing on the fixation of posterior rib fractures utilizing a memory alloy embracing device of rib under thoracoscopy. METHODS: The enrolled patients were divided into the 3D printing (11 patients) and the non-3D printing (18 patients) groups, based on whether a 3D model of ribs was prepared prior to surgery. Analysis was conducted comparing the average fixation time per fracture, postoperative fixation loss, and poor reduction of fractured end between the two groups. RESULTS: The average fixation time of each fracture was 27.2 ± 7.7 min in the 3D printing group and 29.3 ± 8.2 min in the non-3D printing group, with no statistically significant difference observed between the two groups (P > 0.05). The incidence of poor fracture fixation in the 3D printing group was statistically lower than that in the non-3D printing group (12.9% vs. 44.7%, P < 0.05). Further stratified analysis revealed that the off-plate rate in the 3D printing group and the non-3D group was (3.2% vs. 12.8%, P > 0.05), and the dislocation rate of the fractured end was (9.7% vs. 31.9%, P < 0.05). CONCLUSIONS: The application of 3D printing technology to prepare the rib model before surgery is proves beneficial in reducing the occurrence of poor fixation of fractures and achieving precise and individualized treatment.

Diagnostic value of D-dimer for lower extremity deep venous thrombosis caused by rib fracture: a retrospective study.

OBJECTIVE: This study aimed to investigate the role of D-dimer in the diagnosis of lower extremity deep venous thrombosis (DVT) in patients with rib fractures. METHOD: Retrospective analysis was conducted on the clinical data of 499 patients with rib fractures who were admitted to the Third Hospital of Shijiazhuang between October 2020 and September 2021. These patients were divided into the DVT and the non-DVT groups. D-dimer levels were compared between the two groups at 24, 48, and 72 h after the injury. Receiver operating characteristic curves were utilized to evaluate the diagnostic efficacy of dynamically monitoring changes in D-dimer for DVT. RESULTS: The D-dimer levels in the DVT group were significantly higher than those in the non-DVT group at 24, 48, and 72 h after the injury. The area under the curve values for predicting DVT based on D-dimer level at 24, 48, and 72 h after injury in patients with rib fractures were 0.788, 0.605, and 0.568, respectively. CONCLUSION: Detecting D-dimer levels 24 h after the injury can enhance diagnostic efficacy and sensitivity for DVT, thereby reducing the rate of missed diagnoses, which is of great clinical value.

Combined heating and chemical treatment for oil recovery from aging crude oil.

With increasing use of chemical oil displacement agents in tertiary recovery and the application of various demulsifiers for crude oil dehydration, a large amount of aging crude oil containing a high ratio of water is produced, and it is very difficult for processing and utilisation. In this article, we chose aging crude oil samples from a union station in an oilfield in China. Sample composition was analysed to demonstrate that the key of aging crude oil dehydration is the removal of solid impurities. Thus, an efficient method of combining heating and chemical treatments was developed to treat aging crude oil. It includes two steps: The first step is washing of aging crude oil with hot water with sodium dodecylbenzene sulfonate; the second step is chemical demulsification of the above mixture with hydrochloric acid and sodium chloride solution. The result showed that 2.9% of solid impurities and 29.2% of water were removed in the first step; 27.2% of oil, 24.3% of water, and 3.47% of solid impurities in the aging crude oil were recycled in the second step. A total 87.07% of aging crude oil could be solved with this method. The present two-step treatment method can ensure that the dehydration process runs normally and efficiently in the union station, making it a promising method in the recycling of aging crude oil.